’
User s Manual
(English Edition)
Intel Pentium 4
Socket 478 CPU
AMD Athlon / Duron / Athlon XP
Socket 462 CPU
AMD Athlon 64
Socket 754 CPU
CNPS7000A
* Please read before installation
3. Exploded View
Fan
Bolt
Clip
Fan Bracket
Heatsink
Screw for Fan
Screw for
Fan Support
4. Patents
ꢀ
ꢀ
ꢀ
Korean Patent Application No. 00-54635
Korean Design Application Nos. 02-17470, 02-25208, 02-25209, etc.
Patent Applications pending in over 20 nations around the world, including USA, EU,
and Japan
5. Cautions During Installation
1) If excessive force is exerted on the fan, it may malfunction and result in damage to the
product and/or the computer.
2) Do not put your finger into the fan while it is running.
3) Keep the product away from children.
4) Zalman Tech. Co., Ltd. is not responsible for any problems arising from using the product
outside its intended purpose.
5) The exposed core of a Socket 462 CPU can be cracked if proper care is not taken. Read the
“Installation” section thoroughly before installing.
6) Zalman Tech. Co., Ltd. is not responsible for any problems arising from using CNPS7000A
on a Socket 462 CPU.
* The specifications of any product may change without prior notice to improve the performance thereof.
2
5. Components
1) Common Components
❶
❷
❸
❹
❺
FHS Assembly (CNPS7000A-CU/ALCU)
Four Bolts - For fastening the Clip
Thermal Grease
❶
Adjustable Fan Speed Controller (FAN MATE 1)
User’s Manual
❷
❸
❹
❺
❻
2) Components for Intel Pentium 4(Socket 478)
Two (2) Clip Supports - For Socket 478
3) Components for AMD Athlon / Athlon XP(Socket 462)
❻
❼
❽
❾
❿
One(1) A - Type(blue) Clip Supports for AMD Socket 462
One(1) B - Type(white) Clip Supports for AMD Socket 462
Four Bolts - For Fastening the Clip Supports
One Set of Washers
❼
❽
❾
❿
4) Components for AMD Athlon 64(Socket 754)
ꢁ
ꢂ
ꢃ
Two Nipples
One Blackplate
Use Big Hole Washer at Component
❿
ꢁ
ꢂ
6. Compatible CPU Types
1) INTEL Pentium 4 - Socket 478
All current speeds of Pentium 4 Socket 478 CPUs
For CPUs with higher clock speeds than 3.2GHz, please refer to our website
(www.zalmanusa.com).
* The specifications of any product may change without prior notice to improve the performance thereof.
3
Caution)
① As shown in Figure 2 a motherboard that is not compliant with the “10.2mm motherboard
component height restriction” standard, introduced by Intel, may create interference between
components and the clip. Please do not install the CNPS7000A when this interference is observed.
②No components higher than 3.9cm should be present within 5.5cm radius from the center
of the CPU to install this product.
10.2mm Motherboard component height restriction
Clip
Mainboard
component
Top View
Top View
Clip
Mainboard
component
Side View
Side View
Figure 1 (O)
Figure 2 (X)
2) AMD Athlon/Duron/Athlon XP - Socket 462
All CPUs conforming to Socket 462 platform
Caution)
③
②
①This product requires "Heatsink Attach Holes" around CPU
Socket as shown on the right figure.
①
②
No components higher than 3.9cm should be present within
5.5cm radius from the center of the CPU to install this product.
③This product can not be installed if any Motherboard
component(capacitor) taller than 1.5cm is located
under the clip.
4-4bl
④
For more information, refer to “Compatible Motherboard List”
at our website(www.zalmanusa.com).
3) AMD Athlon 64 - Socket 754
is officially released.
* The specifications of any product may change without prior notice to improve the performance thereof.
4
(INTEL Pentium 4-478)
7. Installation
CPU (IHS)
1) Apply Thermal Grease
Spread thermal grease thinly and evenly
over the CPU core.
Thermal Grease
Clip Support
Retention Guide
2) Install Clip Support
Install the two clip supports at both sides
of the retention guide as shown on the
right.
ꢄ
ꢅ
ꢆ
Bolt
3) Insert Bolts
Insert the bolts into the inner holes on the clip.
Outer Hole
Inter Hole
Clip
4) Fasten Bolts
Place the FHS on the center of the CPU.
Screw in both bolts in an alternating
fashion until they are completely tightened.
5) Supply Power
3-Pin Fan
Connect FAN MATE 1 between the
motherboard and the fan.
Connector
FAN MATE 1
Speed Control Knob
(Mainboard)
Mainboard
3-Pin Fan Connector
(CNPS7000A)
* The specifications of any product may change without prior notice to improve the performance thereof.
5
(Athlon/Duron/Athlon XP-462)
8. Installation-AMD
B-Type Clip Support (White)
A-Type Clip Support (Blue)
1) Install Clip Support
Small
Washer
Install the socket 462 Clip Supports
as shown on the right.
Lever
Ensure to install A-Type clip
support(Blue) by the Lever.
M/B
Small
Washer
Bolt
B-Type Clip Support (White)
CPU
2) Apply Thermal Grease
Spread thermal grease thinly and evenly
over the CPU core.
Thermal Grease
Bolt
3) Insert Bolts
Insert the bolts into the inner holes on the clip.
Outer Hole
Inter Hole
Clip
4) Fasten Bolts
Place the FHS on the center of the CPU.
Screw in both bolts in an alternating
fashion until they are completely tightened.
5) Supply Power
3-Pin Fan
Connect FAN MATE 1 between the
motherboard and the fan.
Connector
FAN MATE 1
Speed Control Knob
(Mainboard)
Mainboard
3-Pin Fan Connector
(CNPS7000A)
* The specifications of any product may change without prior notice to improve the performance thereof.
6
(Athlon 64-754)
9. Installation-AMD
1) Fasten Nipples
Nipple
M/B
Locate the backplate on the bottom of the
mohterboard under the CPU socket, then
fasten the nipples as shown on the right.
Big Hole
Washer
ꢇWhen installing CNPS7000A on Athlon
64,Retention Frame is not needed.
Backplate
CPU (IHS)
2) Apply Thermal Grease
Spread thermal grease thinly and evenly
over the CPU core.
Thermal Grease
Bolt
3) Insert Bolts
Insert the bolts into the outer holes on the clip.
Outer Hole
Inter Hole
Clip
4) Fasten Bolts
Place the FHS on the center of the CPU.
Screw in both bolts in an alternating
fashion until they are completely tightened.
5) Supply Power
3-Pin Fan
Connector
(Mainboard)
Connect FAN MATE 1 between the
motherboard and the fan.
FAN MATE 1
Speed Control Knob
Mainboard
3-Pin Fan Connector
(CNPS7000A)
* The specifications of any product may change without prior notice to improve the performance thereof.
7
10. Notes on Usage
1) Checking CPU Compatibility & Using FAN MATE 1
Read “Compatible CPU Types” on page 4 to confirm that your CPU is compatible before using
the CPU cooler. The speed control knob on FAN MATE 1 can be turned to set the fan speed.
When it is turned counter-clockwise, the fan operates in Silent Mode at its minimum speed.
NOTE) FAN MATE 1 has been specifically designed to be used with the fan included in this
product. Zalman Tech. Co., Ltd. is not responsible for any damage caused to systems
or CPUs by using FAN MATE 1 with other types of fans.
2) Cautions During Booting
When booting the computer, it may automatically power down after an alarm sound by a system
monitoring program to indicate that the the CPU fan is rotating slowly. If this happens, turn the
speed control knob fully clockwise to increase the fan speed. Then set ‘CPU Fan Detected’ to
‘Disabled’ in the BIOS settings, or set the slowest rotational speed of the CPU fan in the system
monitoring program to less than or equal to 1300 RPM. Now the fan can be set back to the silent
mode by turning the knob counter clockwise.
NOTE) Some motherboards do not boot if the rotational speed of the CPU fan below a certain
number of RPM. If the BIOS settings are updated, Silent Mode can be used. For more
information on updating your BIOS, please refer to your motherboard manufacturer's
web site. Disabling of CPU fan speed detection in BIOS settings does not effect
computer performance.
3) Creating a Complete Noiseless System
Use the following Zalman products to achieve stable and silent operation of your computer :
Noiseless Power Supply, CNPS series CPU Cooler, Fanless Coolers for Northbridge Chipset &
Video Card, and Noiseless Fan.
11. Thermal Resistance and Noise
* The specifications of any product may change without prior notice to improve the performance thereof.
8
|