OPERATING INSTRUCTIONS
XM RADIO
P/N 08A15-1E1-000
How the service works
The XM service is based on two satellites that have fixed positions over the
equator. One satellite for the east coast of the United States and the other for the
west coast. The two satellites continuously broadcast radio signals throughout the
continental United States.
The XM service also uses ground-based antennas that broadcast into areas that
may be obstructed from satellite radio signal. Not all areas that are obstructed
have ground based antennas as a backup signal. XM radio makes every effort to
minimize the areas that do not receive radio signal.
information.
Note: Service activation and antenna is necessary to receive XM Satellite radio transmission
3
Locations where satellite signals are received easily
Satellite signals are received best in the areas
where there are no tall buildings, trees or tall
objects that can obstruct the signals.
Satellite radio signals may not be received in areas listed below.
There may be ground-based coverage in some of these areas that will provide
uninterrupted service of satellite radio. The XM radio will not operate only when
there is no signal from both satellite and ground-based antennas.
4
Sound in your car
The signal is broadcast in a digital format so that if you do run into a
situation where both the satellite antenna and the ground-based
antenna lose the signal the sound will drop off completely. This
condition would result in no static and may sound as though the unit
were shut off. As soon as the obstruction is cleared or a ground-
based signal is re-established the sound will come back on. If you
do experience a loss of signal, check the display module to make
sure it is powered on and check the display for NO SIGNAL. Refer
to page 15 of this manual for a display of messages.
5
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Initial Setup
Turning power on and off
1. Press the SOURCE POWER button to turn the unit on.
NOTE: The unit can be turned on by pressing any of the buttons of the display module.
2. Press and hold the SOURCE POWER button for 2 seconds or more to turn the
unit off.
NOTE: When turning the unit on and off with the POWER button. Be sure to lower the volume level
of the vehicle’s radio when turning the unit on and off with the POWER button. This will prevent any
electrical popping noises being transmitted from the unit.
6
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Initial Setup
Modulator frequency setting
1. Press and hold the DISP SETUP for 2 seconds or more.
2. Turn the rotary encoder or press the 6 or 5 button to select the frequency
setting mode (displays the frequency of the desired modulation station).
3. Press the 7 or 8 button to set the frequency.
4. The frequency is varied by 200kHz (0.2MHz) steps from 87.7 to 89.9 MHz.
5. Press the DISP SETUP button to return to normal mode.
Note: In order to resume normalAM and FM radio reception, turn the power of the XM radio display
module off. Press and hold the SOURCE POWER button for 2 seconds or more
7
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Initial Setup
XM level setting (XM output level)
When your XM receiver is connected to the factory installed radio, this feature will
allow the user to choose between 4 levels of output (XM level 1 to 4) to better
match the output level of the Honda/ Acura radio.
1. Press and hold the DISP/SETUP button for 2 seconds or more.
2. Turn the rotary encoder or press the 6 or 5 button to select the XM LEV.
3. Press the 7 or 8 button to set the desired volume level. (XM LEV 1 - XM LEV 4)
Level 3 or 4 is recommended.
4. Press DISP/SETUP button to return to normal operation mode.
8
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Initial Setup
Scrolling feature
This feature allows the broadcast text information such as artist, song tittle and
station information to move continuously across the screen. This is the default setting
however this feature can be disabled if the user prefers no scrolling. Below shows
how to disable or enable this feature.
1. Press and hold the SETUP button for 2 seconds or more.
2. Turn the rotary encoder or press the 6 or 5 button to select the SCR.
3. Press the 7 or 8 button to set this feature (ON or OFF)
4. Press setup button to return to normal operation mode.
9
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Operation
Receiving XM channels with the XM receiver
1. Turn the vehicle’s radio on to FM and tune to the XM radio’s modulator fre-
quency (between 88.7 to 89.9). Refer to page 7 for how to set XM radio’s
modulator frequency.
2. Press the POWER button of the display module to turn the XM radio on.
3. Turn the rotary knob to display the desired channel. Pressing and holding
down the 7or8 button on the display will change channels continuously.
10
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Operation
Storing XM channel presets
1. After tuning in the desired channel, press and hold the rotary knob for 2 seconds or
more until the channel name on the display blinks.
2. Turn the rotary knob to select the preset number you want to store.
3. Press the rotary knob within 5 seconds once when the correct preset number is dis-
played.
4. Repeat the procedure to store up to five additional channels.
Note: If you store a channel in a preset memory, which already has a station, the current
channel will be cleared and replaced with the new one.
Receiving stored XM channels
1. Press the 6 or 5 button to access the desired satellite channel in the memory.
11
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Operation
Category search
Category search functionally allows you to search for a specific channel by the category of pro-
gramming it offers, or to surf within a category.
1. Momentarily press the rotary knob to display the category of the channel that is cur-
rently selected.
2. While the category is displayed, turn the rotary knob to select a different category.
Note: You can also press the 7 or 8 button to select a category
3. Within 5 seconds of selecting the category, press the rotary knob to select the next
channel within that category. Repeatedly press the rotary knob within 5 seconds to
select additional channels with in that category.
12
DISP/SETUP
Rotary Knob
8
SOURCE / POWER
5Up
7
Down
6
Operation
Changing the display
Text information, such as the channel name, artist name/feature, and song/program tittle, is
available with each XM channel. This unit can display this text information as explained below
1. Press the DISP SETUP button. Each time you press the button, the display
changes as shown below.
Song tittle
display
Channel name
display
Artist name
display
13
Troubleshooting Guide
If you encounter a problem, please review the items listed below. This guide will help you to isolate
the problem. Make sure the rest of your system is operating properly. If necessary consult your
local authorized Honda dealer.
SYMPTOM
CAUSE
SOLUTION
XM radio will not operate.
Ignition switch is in the off position. Turn Ignition to the on position.
Power to XM radio is
not turned on.
Turn the XM radio on.
Possible blown fuse.
Contact your Honda dealer.
The XM radio appears to be on, Vehicle’s radio volume is set too low Raise radio volume level.
but there is no sound from the
speakers.
Vehicle’s radio not tuned to correct
frequency.
Check radio make sure the
vehicle’s radio is set correctly.
The antenna may not be connected. Contact your Honda dealer.
Big difference in sound level
between car audio system and
XM radio.
XM radio needs Level adjustment. Refer to page 8 in manual.
Poor or no reception for XM.
The antenna may not be connected. Contact your Honda dealer.
14
Display Information
Display messages for XM radio operation
ANTENNA
• The XM antenna is not connected to the XM radio module
- Check whether the XM antenna cable is attached securely to the XM radio module.
UPDATING
• XM radio is being updated with the latest encryption code.
- Wait until encryption code is fully updated. Channel 0 and 1 should function normally.
NO SIGNAL
• XM signal is too weak at the current location.
- Wait until the car reaches a location with stronger signal.
15
Display Information
Display messages for XM radio operation
LOADING
• XM radio is acquiring audio or program information
- Wait until the radio has received the information
OFF AIR
• The channel currently selected has stopped broadcasting.
- Select another channel.
- - - -
• The user selected a channel number that does not exist or is not subscribed to.
-
The unit will revert back to the previously selected channel.
• No artist or tittle information associated with the channel at this time.
-
No action required
16
SPECIFICATIONS
RF MODULATOR UNIT
RF Output Frequency (selectable)
RF Output Voltage
87.7-89.9 MHz
70 dBµV
RF Modulator input Sensitivity/Impedance 500mV/10 k Ohms
Recommended Operating voltage
Recommended Temperature range
13.4 Vdc
14°F– 140F° (-10°C -+60°C)
DISPLAY MODULE
Width
Height
Depth
Weight
113 mm (4-7/16”)
39.5mm (1-9/16”)
19 mm (25/32”)
0.20 kg (7 oz)
FM MODULATOR
Width
130 mm (5-1/8”)
35 mm (1-3/8”)
Height
Depth
Weight
74 mm (2-15/16”)
0.38 kg (13.4 oz)
17
REF. NO. MR0HL210
08A15-1E1-000-81
Printed in U.S.A
© 2003 American Honda Motor Co., Inc - All Rights Reserved.
|