Model D4327/D4328
Quick Release Wood Vise
Instruction Sheet
Introduction
Your new Model D4327/D4328 Quick Release Wood Vise
(Figure 1) is designed to fit on workbenches 21⁄4" and
1
thicker, but can be adapted to workbenches down to 1 ⁄2
thick by using a shim. Holes are pre-drilled in the jaw
faces to attach aftermarket or shop-built wood clamping
vise jaw pads.
"
D4327 Specifications
•
•
•
•
Jaw Width .................................................7"
Mounting Height (Workbench Thickness) ..........21⁄4
"
Maximum Jaw Opening ..................................8"
Weight................................................21 lbs.
D4328 Specifications
Figure 1. Quick release wood vise.
•
•
•
•
Jaw Width .................................................9"
Mounting Height (Workbench Thickness) ..........21⁄4
Maximum Jaw Opening ................................ 10"
Weight................................................25 lbs.
"
Workbench
Shim
Vise
Installation
1. Have another person hold the vise up against the
workbench in the desired mounting location. If the
workbench has holes for bench dogs, make sure the
bench dog on the vise is aligned with those holes.
Figure 2. Shim placed between workbench
and vise for workbenches under 21⁄4".
Note: If the workbench is less than 21⁄4" thick, use a
piece of scrap wood (Figure 2) between the vise and
workbench as a shim. Cut the shim to the necessary
thickness so the vise does not protrude above the
workbench after mounting.
Mounting Holes
for Wood
Screws
2. Pencil mark the workbench through the mounting
Mounting
Holes for Lag
Screws
holes to establish locations to drill pilot holes.
3. Use a 1⁄8" drill bit to drill pilot holes approximately
11⁄2" deep in the face of the workbench, where the
wood screws will be used (see Figure 3).
Figure 3. Mounting hole locations.
COPYRIGHT © MARCH, 2012 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#14922ST
Printed in China
D4327/D4328 - For Models Manufactured Since 3/12
D4327 Parts
4
3
14
13
5
16
18
6
9
17
8
7
10
11
15
21
22
20
2
1
12
19
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
PHLP HD SCR M5-.8 X 12
1
2
XD4327001 FLAT COIL SPRING 4 X 3
XD4327002 SLOTTED NUT M12-1.75
12
13
14
15
16
17
18
19
20
21
22
XPS08M
XD4327013 FINGER BOLT M8-1.25 X 20
XD4327014 LOCK DOG 50 X 25 X 10
XD4327015 QUICK RELEASE LEVER
3
4
5
XD4327003 FIXED HOUSING 180 X 160 X 30
XD4327004 SLIDING HOUSING 110 X 110 X 180
XD4327005 GUIDE ROD 22 X 320
XPW06M
FLAT WASHER 12MM
6
7
8
9
10
11
XD4327006 LEADSCREW 33 X 400
XD4327007 TORSION BAR 26 X 285 X 2
XD4327008 GUIDE ROD SUPPORT
XD4327009 HANDLE BAR W/KNOB
XD4327010 REMOVABLE HANDLE KNOB
XD4327011 RETAINER FORK
XD4327017 COTTER PIN 3 X 40
XD4327018 WAVY WASHER 12MM
XPB04M
HEX BOLT M6-1 X 10
LOCK WASHER 6MM
XPLW03M
XD4327021 QUICK RELEASE HALF NUT
XD4327022 HALF NUT HOUSING BRACKET
Parts breakdown provided for reference only. Not all parts shown are available for purchase.
-3-
D4327/D4328 - For Models Manufactured Since 3/12
D4328 Parts
4
3
14
13
5
16
18
6
9
17
8
7
10
11
15
21
22
20
2
1
12
19
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
PHLP HD SCR M5-.8 X 12
1
2
XD4327001 FLAT COIL SPRING 4 X 3
XD4327002 SLOTTED NUT M12-1.75
12
13
14
15
16
17
18
19
20
21
22
XPS08M
XD4327013 FINGER BOLT M8-1.25 X 20
XD4327014 LOCK DOG 50 X 25 X 10
XD4327015 QUICK RELEASE LEVER
3
XD4328003 FIXED HOUSING 230 X 160 X 30
4
5
6
7
8
9
10
11
XD4328004 SLIDING HOUSING 230 X 110 X 110
XD4328005 GUIDE ROD 22 X 380
XD4328006 LEADSCREW 33 X 460
XD4328007 TORSION BAR 26 X 335 X 2
XD4328008 GUIDE ROD SUPPORT
XD4328009 HANDLE BAR W/KNOB
XD4327010 REMOVABLE HANDLE KNOB
XD4327011 RETAINER FORK
XPW06M
FLAT WASHER 12MM
XD4327017 COTTER PIN 3 X 40
XD4327018 WAVY WASHER 12MM
XPB04M
HEX BOLT M6-1 X 10
LOCK WASHER 6MM
XPLW03M
XD4327021 QUICK RELEASE HALF NUT
XD4327022 HALF NUT HOUSING BRACKET
Parts breakdown provided for reference only. Not all parts shown are available for purchase.
-4-
|