Woodstock Nail Gun W1780 User Manual

MODEL W1780

1¹⁄4" BRAD NAILER

OWNER'S MANUAL

Phone: (360) 734-3482 • Online Technical Support: [email protected]

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT

THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.

#9550TS Printed in China

Model W1780 1¹⁄4" Brad Nailer

SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous

conditions. This manual uses a series of symbols and signal words which are intended

to convey the level of importance of the safety messages. The progression of

symbols is described below. Remember that safety messages by themselves do not

eliminate danger and are not a substitute for proper accident prevention measures.

Indicates an imminently hazardous situation which, if

not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if

not avoided, MAY result in minor or moderate injury.

It may also be used to alert against unsafe practices.

This symbol is used to alert the user to useful

information about proper operation of the

equipment.

NOTICE

Safety Instructions for Pneumatic Tools

5. KEEP CHILDREN AND VISITORS

AWAY. All children and visitors

should be kept at a safe distance

from work area.

1. KEEP ALL SAFETY DEVICES IN

PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking

to see that keys and adjusting

wrenches are removed from tool

before operation.

6. MAKE WORKSHOP CHILD PROOF by

locking your shop and shutting off

air valves.

7. DO NOT FORCE TOOL. It will do

the job better and safer at the rate

for which it was designed.

3. KEEP WORK AREA CLEAN. Cluttered

areas and benches invite accidents.

4. DO NOT USE IN DANGEROUS

ENVIRONMENT. Do not use

8. USE THE RIGHT TOOL. Do not

force tool or attachment to do a

job for which it was not designed.

pneumatic tools in damp or wet

locations, or where any flammable

or noxious fumes may exist. Keep

work area well lighted.

9. DO NOT USE UNDER THE

INFLUENCE OF DRUGS OR

ALCOHOL.

-1-

Model W1780 1¹⁄4" Brad Nailer

Safety Instructions for Pneumatic Tools

17. DISCONNECT TOOLS before

servicing, changing accessories, or

moving to another location.

10. USE PROPER AIR HOSE for the

tool. Make sure your air hose is in

good condition and is long enough

to reach your work without

stretching.

18. DO NOT OVERREACH. Keep proper

footing/balance at all times.

11. WEAR PROPER APPAREL. Do

not wear loose clothing, gloves,

neckties, rings, bracelets, or

other jewelry which may get

caught in moving parts. Non-slip

footwear is recommended. Wear a

protective hair covering to contain

long hair.

19. USE THE RECOMMENDED

ACCESSORIES. Consult owner’s

manual for recommended

accessories. The use of improper

accessories may cause risk of

injury.

20. CHECK FOR DAMAGED PARTS

BEFORE USING. Check for binding

and alignment of parts, broken

parts, part mounting, loose bolts,

and any other conditions that may

affect machine operation. Repair

or replace damaged parts.

12. ALWAYS USE SAFETY GLASSES.

Also use a face or dust mask

if cutting operation is dusty.

Everyday eyeglasses only have

impact resistant lenses, they are

NOT safety glasses.

21. NEVER LEAVE UNATTENDED TOOL

CONNECTED TO AIR. Disconnect

the air hose and do not leave tool

until it is relieved of any built up

pressure.

13. WEAR APPROVED HEARING

PROTECTION. Air escaping from

pneumatic tools can exceed safe

exposure limits and may cause

hearing damage with prolonged

exposure.

22. NEVER ALLOW UNTRAINED

USERS TO USE THIS TOOL WHILE

UNSUPERVISED.

14. SECURE WORK. Use clamps or a

vise to hold work when practical.

It is safer than using your hand

and frees both hands to operate

tool.

23. IF YOU ARE UNSURE OF THE

INTENDED OPERATION, STOP

USING TOOL. Seek formal training

or research books or magazines

that specialize in pneumatic tools.

15. MAINTAIN TOOLS WITH CARE.

Keep tools lubricated and clean

for best and safest performance.

Follow instructions for lubricating

and changing accessories.

24. BE AWARE OF HOSE LOCATION

WHEN USING PNEUMATIC TOOLS.

Hoses can easily become a tripping

hazard when laid across the floor

or spread out in a disorganized

fashion.

16. REDUCE THE RISK OF

UNINTENTIONAL FIRING. Do not

carry tool with hand on trigger

and always disconnect from air

when not in use.

-2-

Model W1780 1¹⁄4" Brad Nailer

Additional Safety for Nailers/Staplers

1. HAND INJURIES: Do not place your

hands near the nail point of entry.

A nail can deflect and tear through

the surface of the workpiece,

5. HOSE USAGE: Make sure your air

hose is designed for the tool in

use, is in good condition, and is

long enough to reach your work

without stretching. However, an

overly long air hose in the work

area may be a tripping hazard.

puncturing your hand or fingers.

2. COMBUSTIBLE GASES: Never

connect the nailer to pressurized

oxygen or other combustible

gases as a power source. Only use

filtered, lubricated, and regulated

compressed air.

6. OPERATING QUESTIONS: If you

are not sure about the intended

operation, stop using the nailer.

Seek formal training.

3. SAFE HANDLING: Never point

the nailer at others! Do not keep

the trigger pulled when loading

fasteners, carrying, or holding

tool. Carry the nailer only by the

handle, never by any other part.

Do not carry the nailer by the air

hose. Disconnect the nailer from

the air hose when going up and

down ladders.

7. MAINTENANCE: Always disconnect

air from the nailer when servicing

or installing nails. During

maintenance, a nailer connected to

air may fire accidentally, causing

serious personal injury.

8. COMPRESSED AIR RATING: Do not

connect the nailer to compressed

air that exceeds 120 PSI.

9. CHECK VALVE: Do not use a check

valve or any other fitting that

4. CLEANING: Never use gasoline or

other flammable liquids to clean

the nailer; vapors in the nailer will

ignite by a spark and cause it to

explode.

allows air to remain in the tool.

10. MODIFICATIONS: DO NOT modify

this tool or bypass the safety nose

mechanism.

Never point this nailer at yourself

or another person! Always pay

attention to the direction this nailer

is pointed. Use this tool with respect

and caution to lessen the possibility

of operator or bystander injury.

Ignoring this warning may result in

serious personal injury.

Nailer/stapler accidents routinely

happen while moving the gun to

another location, such as up ladders,

to another room, or even another

job site. Always disconnect the gun

immediately after use and never

transport the gun while connected to

the air—even if the air compressor is

disconnected from its power source!

-3-

Model W1780 1¹⁄4" Brad Nailer

INTRODUCTION

Woodstock Technical

Support

Tool Data

Nail Size............................. 18 Gauge

Nail Length........................... ³⁄8"–1¹⁄4

Magazine Capacity................. 100 Nails

Air Inlet................................¹⁄4" NPT

Weight.................................3¹⁄4 lbs.

Operating Pressure ...............60–100 PSI

This Model W1780 1¹⁄4" Brad Nailer has

been specially designed to provide many

years of trouble-free service. Close atten-

tion to detail, ruggedly built parts and a

rigid quality control program assure safe

and reliable operation.

Woodstock International, Inc. is commit-

ted to customer satisfaction. Our intent

with this manual is to include the basic

information for safety, setup, operation,

maintenance, and service of this product.

We stand behind our tools! In the

event that questions arise about your

machine, please contact Woodstock

International Technical Support at

(360) 734-3482 or send e-mail to:

[email protected]. Our knowl-

edgeable staff will help you troubleshoot

problems and process warranty claims.

Read the manual before operation.

Become familiar with this nailer, its

safety instructions, and its operation

before beginning any work. Serious

personal injury may result if safety

or operational information is not

understood or followed.

If you need the latest edition of this

manual, you can download it from

http://www.shopfox.biz.

If you have comments about this

manual, please contact us at:

No list of safety guidelines can be

complete. Every shop environment

is different. Always consider safety

first, as it applies to your individual

working conditions. Use this and

other tools with caution and respect.

Failure to do so could result in serious

personal injury, damage to equipment

or poor work results.

Woodstock International, Inc.

Attn: Technical Documentation

Manager

P.O. Box 2309

Bellingham, WA 98227

Email: [email protected]

-4-

Model W1780 1¹⁄4" Brad Nailer

Compressed Air System

The Model W1780 is designed to be

operated at 60-100 PSI using clean,

dry, regulated, compressed air. Do not

exceed the 120 PSI maximum pressure

for your model.

Before using your new nailer, regulate

the air pressure to the minimum PSI for

your model.

An in-line filter/lubricator/regulator unit

can be installed as depicted in Figure 1.

Exceeding the maximum permissible

operating pressure may damage the

nailer and cause it to malfunction.

To protect yourself from personal

injury, DONOTallowtheairpressure

to exceed the recommended

pressure for this nailer!

This filter/lubricator/regulator unit

will protect your tool from damaging

water build-up, allow you to adjust and

maintain regulated air pressure, and

save you the inconvenience of having to

manually lubricate your tool every time

you use it.

If you plan on installing a filter/

lubricator/regulator unit in your

compressed air system, always follow the

connection instructions that come with

the unit.

��

Figure 1. Typical filter/lubricator/regulator installation order.

-5-

Model W1780 1¹⁄4" Brad Nailer

SETUP

Unpacking

This brad nailer has been carefully packaged for safe transportation. If you notice the

machine has been damaged during shipping, please contact your authorized Shop Fox

dealer immediately.

Inventory

The following is a description of the main components shipped with the Model W1780.

Lay the components out to inventory them.

Note: If you can't find an item on this list, check the mounting location on the tool

or examine the packaging materials carefully. Occasionally we pre-install certain

components for safer shipping.

Model W1780 Inventory

Qty

A. Brad Nailer............................... 1

B. Pneumatic Tool Oil ..................... 1

C. Hex Wrench 3mm ....................... 1

D. Hex Wrench 4mm ....................... 1

E. Carrying Case............................ 1

-6-

Model W1780 1¹⁄4" Brad Nailer

— If the nailer fires when the trigger

is pulled, without the safety nose

mechanism being depressed, then

the nailer is not working properly.

Safety Nose Mechanism

A safety mechanism on the nose of

the nailer protects against accidental

firing. When the trigger is pressed, the

nailer will not fire until the safety nose

mechanism is depressed.

— If you find that the safety

nose mechanism is not working

properly, check the lubrication of

its sliding components.

Before you use your nailer for the first

time, check the safety nose mechanism

to ensure proper function.

To check the safety nose mechanism,

do these steps:

DO NOT attempt to modify or bypass

the safety nose mechanism to make

the nailer/stapler fire without

pushing the safety nose down.

1. DISCONNECT NAILER FROM THE AIR

SUPPLY!

2. Make sure the magazine is empty and

contains no nails.

Thesafetymechanismisamechanical

device that can fail. Never rely on this

mechanism as an excuse to point the

nailer at yourself or any bystanders.

Serious injury may occur.

3. Make sure the trigger and the safety

nose mechanism move up and down

without sticking.

4. Connect the nailer to the air supply.

5. Without pressing the trigger,

depress the safety nose mechanism

against a scrap piece of wood that is

clean and free of any knots, nails, or

other foreign objects.

— If the nailer does not fire, then

the safety nose mechanism is

working correctly.

— If the nailer does fire when you do

this, immediately disconnect the

nailer from the air supply and call

Technical Support.

Operating this nailer can propel

objectsintotheair,causingimmediate

eye damage. To protect yourself,

always wear ANSI approved safety

glasses or goggles when operating this

equipment.

-7-

Model W1780 1¹⁄4" Brad Nailer

OPERATIONS

When replacing nails in your Model

W1780, follow these guidelines:

Gauge:........................................18

Length: ............................... ⁄8"–1 ⁄4

Capacity:................................... 100

To load your nailer, do these steps:

Figure 3. Loading nails into magazine.

1. DISCONNECT NAILER FROM THE AIR

4. Slide the nails all the way down to

SUPPLY!

the nose of the nailer.

2. Grip the nailer firmly, and pull the

magazine pusher back until the catch

lever engages, as shown in Figure 2.

5. Release the magazine pusher by

pulling back on the pusher and

pushing in on the catch lever.

Catch Lever

Operating

If you have not read the safety

instructions in this manual, do not

operate the nailer.

Pusher

Before you operate your nailer, place five

to six drops of the included oil into the

quick connect fitting where the nailer

connects to the air supply.

Figure 2. Sliding magazine pusher back

and engaging catch lever.

3. Insert a strip of nails, pointed-end

down, into the magazine, as shown in

Figure 3.

To operate your nailer, do these steps:

1. Connect the air supply to the quick

connect fitting.

2. To test for proper nail penetration,

hold the nailer perpendicular to the

surface of a piece of clean scrap

wood that is thick enough for the

length of nails you have loaded.

-8-

Model W1780 1¹⁄4" Brad Nailer

3. Depress the safety nose mechanism

Adjusting Depth

against your workpiece.

A depth adjustment knob is attached to

the nose for setting the nail depth.

4. Before pulling the trigger, make sure

your free hand and other body parts

are positioned out of the way of a

potential path of a nail in case of

deflection.

To adjust the depth, do these steps:

1. DISCONNECT NAILER FROM THE AIR

SUPPLY!

Deflection is caused when grain

irregularities, knots or foreign objects

inside the wood cause the nail to

change its path, resulting in the

nail puncturing the surface of the

workpiece, as shown in Figure 4.

2. Rotate the adjustment knob (Figure

5) clockwise to increase the nail

depth, and counterclockwise to

decrease the nail depth.

Besides damaging your workpiece,

deflection can cause injury if your

free hand is securing the workpiece in

the location that the nail deflects.

Safety Nose

Adjustment

Knob

Figure 5. Depth adjustment controls.

3. Connect nailer to the air supply and

test the nail depth, and repeat this

entire procedure if necessary until

the nail depth is satisfactory.

Figure 4. Example of nail deflection.

5. Pull the trigger.

DO NOT place your hands near the

nail point of entry. A nail can deflect

and tear through the surface of the

workpiece, puncturing your hand or

fingers.

— If the nail drove into the wood

far enough, continue with your

intended operations.

— If the nail either went too far or

not far enough, then go to the

Adjusting Depth section on this

page.

-9-

Model W1780 1¹⁄4" Brad Nailer

Clearing Jammed Nails

Nose Release

A jammed nail must be cleared before

using the nailer again.

To clear a jammed nail from the dis-

charge area, do these steps:

Nose

Tip

1. DISCONNECT NAILER FROM THE AIR

Nose Cover

SUPPLY!

Figure 6. Nose opened to clear a jam.

2. Pull back and latch the magazine

5. Dislodge the jammed nail with a

tool that will fit in the slot on the

underside of the nose.

pusher.

3. Remove the nail stick from the

magazine.

6. Throw the damaged nail away and

insert a new nail stick that only

contains clean, undamaged nails. DO

NOT use dirty or damaged nails!

4. Open the nailer nose by removing the

rubber nose tip, squeezing the nose

release mechanism (Figure 6), and

opening the nose cover.

7. Close the nose cover and re-install

the nose tip.

8. Release the catch lever and let

the pusher slide to the front of the

magazine.

-10-

Model W1780 1¹⁄4" Brad Nailer

6. Open the nose cover as if to clear a

Replacing Pistons/

O-Rings

Under heavy use, a piston or piston shaft

may wear out. Replacement is quick and

easy. Contact your authorized Shop Fox

dealer to obtain the Piston Repair Kit

(Part Number X1780004).

jammed nail.

7. Watch the discharge area and push

the top of the piston with your

finger. You will see the piston shaft

slide down the discharge area.

8. Taking care not to scratch or dent

the nailer parts, use a wooden dowel

or similarly shaped tool to push the

piston shaft back inside the nailer

until you can grip the piston head and

remove it from the cylinder. Clean

inspect the parts for cracks, wear, or

burrs.

9. Place a new O-ring on the new piston

and apply a thin film of the nailer

lubricating oil on the O-ring.

Always disconnect air from nailer

whenever

servicing!

During

10. Insert the new piston in the cylinder.

Make sure that the grooves on the

piston shaft line up with those on the

guide at the bottom of the cylinder.

The new piston should easily slide

into the cylinder. DO NOT force the

piston into the cylinder! If the piston

is not easily inserted, double-check

the alignment of the piston shaft with

the grooves on the guide.

maintenance, a nailer connected

to air may fire accidentally, causing

serious personal injury!

To replace a piston, do these steps:

1. DISCONNECT NAILER FROM THE AIR

SUPPLY!

2. Remove all nails from the magazine

cartridge, and clean the exterior of

the nailer.

11. After the piston is inserted correctly,

close the magazine. Replace the rear

cap assembly and tighten the four

cap screws.

3. Remove the four cap screws on the

back of the nailer, near the exhaust

port.

12. For more assistance, or to install a

complete O-ring set, refer to the

appropriate breakdown diagram

in the back of this manual for

component locations.

4. Remove the cap.

5. The top of the piston should now be

visible inside the cylinder, which is

housed in the head of the nailer.

-11-

Model W1780 1¹⁄4" Brad Nailer

CLEANING & LUBRICATION

Cleaning

Use a good solvent to clean the nose

assembly of the nailer. Always be sure

that the nailer is dry before using it

again.

Lubricating

Standard pneumatic tool oil has been

included with your new Shop Fox nailer

to help maintain its useful life. Place two

to six drops of oil in the nailer air inlet

(as shown in Figure 7) before every use,

or after 2 hours of continuous use.

Do not allow dust, chips, sand, etc.

into the air connectors or into the body

of the nailer; this may result in leaks

and damage to the nailer and the air

couplings.

Wipe off any excess oil near the nailer

exhaust to avoid dust build-up. When the

oil that was included with the nailer has

been completely used, replace with a

quality pneumatic tool oil.

Another option to manual oiling would

be to install a lubricator in your air

compressor line. If your air compressor

line already has a lubricator, then regular

lubrication of your nailer will not be

necessary. Just make sure there is always

oil in the lubricator.

Never clean this tool with gasoline

or other flammable liquids. Vapors

in the tool may ignite, causing

the tool to explode. Ignoring

this warning may lead to serious

personal injury or even death!

Figure 7. Lubricating nailer via air inlet.

-12-

Model W1780 1¹⁄4" Brad Nailer

W1780 PARTS BREAKDOWN

��

�

��

�

��

�

��

�

��

�

-13-

Model W1780 1¹⁄4" Brad Nailer

W1780 PARTS LIST

DESCRIPTION

REF PART�#

DESCRIPTION

REF PART�#

XPAW04M HEX�WRENCH�4MM

XPAW03M HEX�WRENCH�3MM

X1780003 CARRYING�CASE

X1780004 PISTON�REPAIR�KIT

X1780005 AIR�PLUG�1/4�NPT

X1780006 END�CAP

44 X1780044 SAFETY�PLATE

45 X1780045 TRIGGER

46 X1780046 COMPRESSION�SPRING

47 X1780047 O-RING�13.2�X�1.9

48 X1780048 SWITCH�BRACKET

49 X1780049 O-RING�11.2�X�1.6

50 X1780050 SWITCH�SHAFT

51 X1780051 O-RING�1.9�X�1.1

52 X1780052 COMPRESSION�SPRING

53 X1780053 TRIGGER�VALVE�GUIDE

54 X1780054 O-RING�7�X�1.5

55 X1780055 SAFETY�GUARD

56 X1780056 COMPRESSION�SPRING

57 X1780057 ADJUSTMENT�BOLT

58 X1780058 ROLL�PIN�1.5�X�8

59 X1780059 SLIDING�BRACKET

60 X1780060 COMPRESSION�SPRING

X1780007 O-RING��40�X�2.65

X1780008 LOCK�NUT�M3-.5

X1780009 RUBBER�HANDGRIP

10 XPSB23M

CAP�SCREW�M4-.7�X�12

11 X1780011 SAFETY�GUARD�CLAMP

12 X1780012 MAGAZINE�HOUSING

13 X1780013 MAG.�CONNECTOR�PLATE

14 XPSB18M

15 X1780015 CATCH�LEVER

16 XPRP42M ROLL�PIN�3�X�20

CAP�SCREW�M4-.7�X�8

17 X1780017 TORSION�SPRING

18 X1780018 MAGAZINE�BRACKET

61 XPRP55M

ROLL�PIN�3�X�27

19 XPSB56M

CAP�SCREW�M3-.5�X�10

62 X1780062 BRACKET

20 X1780020 COMPRESSION�SPRING

21 X1780021 SPRING�CAP

63 X1780063 GUN�BODY

64 X1780064 PISTON�SLOT�WASHER

65 X1780065 BUMPER

22 X1780022 MAGAZINE�SLIDE�PLATE

23 XPSS23M

SET�SCREW�M4-.7�X�10

66 X1780066 CYLINDER

24 X1780024 MOVABLE�MAGAZINE

25 X1780025 INLAY�STRIP

67 X1780067 COLLAR

68 X1780068 O-RING�48.7�X�2.65

69 X1780069 MAIN�PISTON

70 X1780070 O-RING��23.5�X�2

71 X1780071 O-RING�30�X�3

72 X1780072 GASKET

26 XPSB158M CAP�SCREW�M3-.5�X�16

27 X1780027 SAFETY�GUARD�CLAMP

28 XPSB16M

CAP�SCREW�M4-.7�X�16

29 X1780029 DRIVER�GUIDE

30 X1780030 MOVABLE�NOSE�COVER

73 X1780073 SWITCH�PISTON

74 X1780074 O-RING�33.6�X�2

75 X1780075 COMPRESSION�SPRING

76 X1780076 O-RING�17�X�2.65

77 X1780077 SEALING�WASHER�18MM

78 X1780078 CYLINDER�CAP

79 XPLW01M LOCK�WASHER�5MM

31 XPRP61M

ROLL�PIN�3�X�12

32 X1780032 NOSE�COVER

33 XPSB110M CAP�SCREW�M4-.7�X�6

34 X1780034 HANDLE

35 X1780035 HANDLE�COVER

36 X1780036 SLIDE�BRACKET

37 X1780037 COMPRESSION�SPRING

38 X1780038 NOSE�COVER�LOCKING�PIN

80 XPSB15M

CAP�SCREW�M5-.8�X�20

81 X1780081 EXHAUST�PORT

39 XPRP18M

ROLL�PIN�4�X�12

82 X1780082 COMPRESSION�SPRING

83 X1780083 SHOULDER�BOLT�M4-.7�X�16

84 X1780084 ORIENTATION�SPRING

85 X1780085 STEEL�BALL

40 X1780040 TORSION�SPRING

41 XPSB15M

CAP�SCREW�M5-.8�X�20

42 X1780042 GUIDE�BRACKET

43 XPRP64M

ROLL�PIN�3�X�18

-14-

Model W1780 1¹⁄4" Brad Nailer

Troubleshooting

Symptom

Possible Cause

Possible Solution

1. O-rings must be replaced

& operation of safety nose

must be checked.

Air leaking at

1. O-rings in trigger valve

housing are damaged.

trigger valve area.

Air leaking between 1. Loose screws in housing.

1. Tighten screws.

2. Replace O-ring

3. Tighten air fitting & use

teflon tape.

housing and hose

2. Damaged O-ring.

3. Loose air fitting.

Air leaking between 1. Damaged seal.

housing and cap.

1. Replace damaged seals.

Tool skips nails

while discharging.

1. Excessive air pressure.

2. Air leaks.

3. Dirt in nose.

1. Reduce air pressure to tool.

2. Tighten screws and fittings.

3. Clean nose.

4. Dirt or damage prevents nails 4. Clean magazine and

from moving freely.

5. Inadequate air flow to tool.

inspect/repair damage.

5. Check fittings, hose,

compressor, and air

pressure.

6. Worn piston O-ring or lack of

lubrication.

6. Replace O-ring and

lubricate.

7. Damaged trigger valve O-rings. 7. Replace trigger valve O-

rings.

8. Worn bumper.

9. Cap seal leaking.

8. Replace bumper.

9. Replace cap seal.

Tool runs slowly or 1. Undersized air hose.

has a loss of power.

1. Use a larger hose.

2. Lubricate nailer.

3. Replace spring.

2. Nailer is not lubricated.

3. Broken spring in cap assembly.

4. Clean or replace damaged

internal parts.

4. Exhaust port in cap is blocked.

Fasteners

1. Nails are the wrong size.

1. Use correct nails.

2. Use undamaged, clean

nails.

frequently jam the 2. Nails are bent or dirty.

nailer.

3. Magazine or nose screws are

loose.

4. Driver or driver guide are

worn or damaged.

3. Tighten magazine.

4. Replace worn or damaged

parts.

5. Nails are wrong angle.

5. Use correct angle nails.

Nailer does not

fire.

1. Nailer is not lubricated.

1. Follow lubricating

instructions.

2. Nail is jammed in magazine or 2. Clear nailer magazine or

discharge area.

3. Piston shaft is damaged.

4. Air pressure too low.

discharge area.

3. Replace piston shaft.

4. Check/increase air

pressure.

Air blows out of

exhaust cap; nailer

will not fire.

1. O-ring slipped out of groove or 1. Reinstall/replace suspect

damaged inside nailer.

O-ring; turn down air

pressure.

-15-

��

Warranty Registration

Name___________________________________________________________________________________

Street __________________________________________________________________________________

City _________________________State___________________________Zip________________________

Phone #______________________Email __________________________Invoice #___________________

Model #_________Serial #______________Dealer Name__________________Purchase Date___________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us

develop better products and services. Of course, all information is strictly confidential.

1. How did you learn about us?

_____ Advertisement

____ Friend

____ Website

____ Local Store

____ Other:

_____ Mail Order Catalog

2. How long have you been a woodworker/metalworker?

_____ 0-2 Years

_____ 2-8 Years

____8-20 Years

_____ 20+ Years

3. How many of your machines or tools are Shop Fox?

_____ 0-2 _____ 3-5

____6-9

_____ 10+

____ No

4. Do you think your machine represents a good value?

_____ Yes

5. Would you recommend Shop Fox products to a friend? _____ Yes

6. What is your age group?

_____ 20-29

_____ 50-59

____ 30-39

____ 60-69

____ 40-49

____ 70+

7. What is your annual household income?

_____ $20,000-$29,000

_____ $50,000-$59,000

____ $30,000-$39,000

____ $60,000-$69,000

____ $40,000-$49,000

____ $70,000+

8. Which of the following magazines do you subscribe to?

____ Cabinet Maker

____ Family Handyman

____ Hand Loader

____ Popular Mechanics

____ Popular Science

____ Popular Woodworking

____ Practical Homeowner

____ Precision Shooter

____ Projects in Metal

____ RC Modeler

____ Today’s Homeowner

____ Wood

____ Wooden Boat

____ Woodshop News

____ Woodsmith

____ Handy

____ Home Shop Machinist

____ Journal of Light Cont.

____ Live Steam

____ Model Airplane News

____ Modeltec

____ Old House Journal

____ Woodwork

____ Woodworker West

____ Woodworker’s Journal

____ Other:

____ Riﬂe

____ Shop Notes

____ Shotgun News

9. Comments:__________________________________________________________________

_____________________________________________________________________________

___________________________________________________________________

FOLD ALONG DOTTED LINE

Place

Stamp

Here

WOODSTOCK INTERNATIONAL INC.

P.O. BOX 2309

BELLINGHAM, WA 98227-2309

FOLD ALONG DOTTED LINE

TAPE ALONG EDGES--PLEASE DO NOT STAPLE

Weider Home Gym WESY85201 User Manual
Weslo Treadmill 831294620 User Manual
Whirlpool Air Conditioner 4380701 User Manual
Whirlpool Cable Box ET4WSKXKQ02 User Manual
Xerox Computer Monitor XR3 Series User Manual
Xerox Copier N4525 User Manual
Yamaha Offroad Vehicle DIC183 User Manual
Zanussi Refrigerator 102294 User Manual
Zanussi Ventilation Hood ZHC 613 User Manual
Zenoah Trimmer eHT600D User Manual