INSTALLATION INSTRUCTIONS
HOOD MODELS – WSL, WCL, & WER
By CNP INDUSTRIES, INC.
P.O. Box 18645 Anaheim, Ca 92817 (877) 387-6721
PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING.
INSTALLATIONS MUST COMPLY WITH ALL LOCAL CODES.
IMPORTANT: Save these Instructions for the Local Electrical Inspector's use.
INSTALLER: Please leave these Installation Instructions with this unit for owner.
OWNER: Please retain these Instructions for future reference
IMPROTANT SAFETY INSTRUCTIONS
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
HOODS SHOULD BR INSTALLED WITH VENTILATORS APPROVED FOR USE WITH THE HOOD.
SEE TABLE – 1 OF THIS INSTRUCTION FOR APPROVED VENTILATORS.
C. When cutting or drilling into wall or
ceiling, do not damage electrical wiring
and other hidden utilities.
B. Sufficient air is needed for proper
combustion and exhausting of gases
through the flue (chimney) of fuel
burning equipment to prevent
backdrafting. Follow the heating
equipment manufactures guideline and
safety standard such as those published
by the National Fire Protection
Association (NFPA) and the American
Society for Heating, Refrigeration and
Air Conditioning Engineers (ASHRAE),
and the local code authorities.
WARNING - TO REDUCE THE
RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO
PERSONS, OBSERVE THE
FOLLOWING:
A. Installation work and Electrical
Wiring Must be Be Done By Qualified
Person(s) In Accordance With All
Applicable Codes & Standards.
Including Fire-Rated Construction.
“WARNING” To Reduce The Risk Of
Fire, Use Only Metal Duct Work.
D. Before Servicing or Cleaning Unit,
Switch Power off At Service Panel And
Lock Service Disconnecting Means to
Prevent Power From Being Switched On
Accidentally. When The Service
Disconnecting Means Cannot be Locked,
securely Fasten A Prominent Warning
Device, Such As A Tag, To The Service
Panel
CAUTION - TO REDUCE THE RISK OF FIRE AND TO PROPERLY EXHAUST AIR, BE SURE TO
DUCT AIR OUTSIDE FOR DUCTED FANS – DO NOT VENT EXHAUST AIR INTO SPACE WITHIN
WALLS OR CEILING OR INTO ATTICS, CRAWL SPACES OR GARAGES.
Read this instruction completely before starting installation. Planning the complete installation before starting any work is
highly recommended. This includes all aspects of the installation including hood location, ducting, electrical requirements,
and adequacy of mounting surfaces.
This hood has been designed to be used with the ventilators shown in Table-1.
Before cutting into cabinets, it is necessary to confirm that the correct ventilator
is being used. Your dealer should have reviewed your needs prior to your
purchase. Be sure you have the correct ventilation system.
TABLE - 1
Use model VEN030I or VEN060I
for internal ventilator. Use
VEN060E, VEN120E, VEN100E
or VEN140E for remote ventilator
CAUTION: To Reduce The Risk Of Fire And Electrical Shock, Install This
Rangehood Only With Blowers Manufactured By Wind Crest.
DUCTING: Use a minimum 8" round duct for VEN030I, VEN060I and VEN060E installations. Use a minimum 10" round
duct for VEN120E, VEN100E, VEN140E and VEN060I-Dual installations. Use #10100 8" - round transition or #10287 10"-
round transition from hood to ducting. Other Transition options are available – See your Dealer for details.
RECEPTACLE
PLUG
POWER SUPPLY
L1
N
G
RECEPTACLE
BOX
BLOWER
MOTOR
18 B # 12
18 G # 11
18 W # 25
18 W
1
2
3
4
1
2
3
4
18 B
18 R
18 B # 24
18 BL #23
18 R # 22
18 BL
18 W # 13
18 BL # 3
18 B # 2
18 W # 10
18 R # 4
18 B # 7
18 W # 9
LEFT
RIGHT
LIGHT
LIGHT
1
3-SPD
A
1
2
5
3
LIGHT
SWITCH
ROTARY
SWITCH
18 B # 6
2
3
4
6
B
18 B # 8
18 W # 5
WIRING DIAGRAM-INTERNAL BLOWER & LIGHTING
RECEPTACLE
POWER SUPPLY
L1
PLUG
N
G
RECEPTACLE
BLOWER
MOTOR
BOX
18 B # 12
18 G # 11
18 W # 25
18 W
1
2
3
4
1
2
3
4
18 B
18 R
18 B # 24
18 BL #23
18 R # 22
18 BL
18 W # 13
RIGHT
HEAT
LIGHT
LEFT
HEAT
LIGHT
18 B # 19
18 B # 17
18 W # 20
18 B # 18
18 W # 26
18 B # 16
18 W # 21
18 BL # 3
18 B # 2
18 W # 10
18 R # 4
18 B # 7
RIGHT
LIGHT
18 W # 9
LEFT
LIGHT
1
HEAT
LIGHT
SWITCH
RIGHT
3-SPD
ROTARY
SWITCH
HEAT
A
1
2
1
2
1
2
5
3
6
LIGHT
SWITCH
LIGHT
SWITCH
LEFT
18 B # 6
2
3
4
B
18 W # 5
18 B # 14
18 B # 15
18 B # 8
WIRING DIAGRAM-INTERNAL BLOWER, LIGHTING & HEAT LAMPS
Dual Internal Ventilators
NOTE: Wiring harness #10220 is required to complete the installation
of dual VEN060I ventilators and must be ordered separately.
Cabinet Mounting
When using two (2) VEN060I ventilators the cabinet mounting must accommodate two discharge transitions. Wiring
and discharge holes are shown in FIG – 6.
HINT: Transition dimensions may very. Before assembling transitions to hood, fit them into the prepared cabinet
opening to be sure the openings are large enough to accommodate the transition. Enlarge the hole if required
Hood Preparation
The hood must be prepared for dual ventilator mountings by removing the discharge coverplate and two “breakaway”
discharge hole plates. To remove, break the metal webs holding the plate and remove completely. See FIG – 5. Break the
metal webs by placing a screwdriver at one corner of the plate and hitting screwdriver sharply with a hammer. After breaking
a second web the plate can be flexed to break other webs.
Wear eye protection when using tools.
Attach the transition (See DUCTING, pg 1), obtained separately from your local hardware or available through your dealer,
and install the hood as described previously in this instruction.
Ventilator Installation
Install the ventilators as previously described, see FIG – 1 and instruction on same page of this document. Connect the
ventilators to the receptacle in the hood junction box using Harness #10220, ordered separately. Dress the wires and
secure to bracket “A” see FIG – 5, using the wire tie supplied with the harness. Follow the remaining instructions for
operating checks to complete the installation.
FIG - 5
AIR DISCHARGE
KNOCKOUTS
AIR DISCHARGE
KNOCKOUTS
HOOD TOP
TIE
HOOD BACK
"A"
|