Model No. WETL0254.0
Serial No.
USER’S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, please call:
8457 089 009
Or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4
Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
e-mail: [email protected]
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
BEFORE YOU BEGIN
Thank you for selecting the new WESLO® CARDIO-
STRIDE ULTIMA treadmill. The CARDIOSTRIDE
ULTIMA treadmill is designed to let you enjoy effective
cardiovascular workouts in the comfort and conve-
nience of your home. And when the CARDIOSTRIDE
ULTIMA treadmill is not in use, it can be folded up,
requiring less than half the space of other treadmills.
ing this manual, please call our Customer Service
Department at 08457 089 009. To help us assist you,
please note the product model number and serial
number before calling. The model number is
WETL0254.0. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual to find the location of the decal).
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Before reading further, please familiarise yourself with
the parts that are labelled in the drawing below.
Console
Warning Decal
Storage Pin
Handrail
The decal shown above has been
placed on the treadmill in the location
shown. If the decal is missing or illegi-
ble, call our Customer Service
Department at 08457 089 009 and
order a free replacement decal. Apply
the decal in the location shown.
Resistance
Control
Walking Belt
Hood
Roller Guards
Rear Roller Adjustment Bolts
3
ASSEMBLY
The help of a second person is recommended. Set the treadmill in a cleared area and remove all packing
materials. Do not dispose of the packing materials until assembly is completed. Assembly requires only the
included hex key
and wrench
.
1. Identify the Right Upright (36); the Resistance
Control/Cable (44) is routed through the Right Upright.
Place the Base (14) near the Right Upright and the
Frame (29). Have another person hold the Right Upright
against the Base as shown.
1
44
36
13
Bracket
37
14
Attach the Right Upright (36) to the Base (14) with two
M8 x 63mm Bolts (38), two M8 Curved Washers (37),
and two M8 Nylon Nuts (13) as shown. Make sure that
the Curved Washers are turned so they conform to the
curve of the Base. Do not tighten the Nylon Nuts yet.
Holes
35
37
13
37
38
13
38
Attach the Left Upright (35) to the Base (14) in the same
way. Make sure that the Left Upright is oriented so the
two indicated holes are on the side shown. Do not tight-
en the Nylon Nuts yet.
37
2a.Raise the Left Upright (35) and the Right Upright (36) to
the position shown. Place the front of the Frame (29)
between the Left Upright and the Right Upright. Connect
the Reed Switch Wire (6) to the Short Reed Switch Wire
(A).
2a
29
36
6
35
A
2b.Attach the Hood (28) to the front of the Frame (29) with
two M5 x 10mm Bolts (10).
2b
10
28
29
10
3. See drawing 3a. Locate the small incline knob on each
side of the Frame. Slide the knobs into one of the three
sets of slots in the brackets on the Uprights. Make sure
that the knobs are fully inserted at the same height.
3a
3b
View from
beneath
35
Knob
9
Bracket
29
Look under the Frame (29) near the Left Upright (35).
See drawing 3b. Locate the Clip (11) attached to the
underside of the Frame. Insert the Reed Switch (6) into
the Clip as shown. Next, locate the Magnet (12) on the
left Flywheel (9). Turn the Flywheel until the Magnet is
aligned with the Reed Switch. Move the Reed Switch
so that there is a 3 mm (1/8 in.) gap between the
Reed Switch and the Magnet. Then, tighten the M4 x
12mm Screw (3) in the Clip.
3
11
6
12
3 mm
29
4
4. Hold the Handrail (5) near the Left and Right Uprights (35,
36). Connect the Handrail Wire (2) to the Reed Switch
Wire (6). Insert the Wires down into the Left Upright.
4
33
34
5
2
Attach the Handrail (5) to the Uprights (35, 36) with four
M8 x 15mm Bolts (33) and four M8 Washers (34). Be
careful not to pinch the Wires (2, 6).
6
See step 1. Tighten the four M8 Nylon Nuts (13).
34
35
Attach the Resistance Control (44) to the Right Upright
(36) with the M5 x 12mm Bolt (46) and the M5 Washer
(47).
33
46
47
36
44
5. The Console (1) requires two “AAA” batteries. Alkaline
batteries are recommended. Press the indicated tab on
the Battery Cover (27), and remove the Battery Cover.
Insert two batteries into the two battery clips; make sure
that the negative (–) ends of the batteries are touch-
ing the springs in the battery clips.
5
Batteries
1
Tab
27
6. See drawing 6a. Hold the Console (1) near the Handrail
(5). Connect the wire on the Console to the Handrail
Wire (2). Attach the Console to the Handrail with two M4
x 12mm Screws (3). Make sure that the wires are not
pinched.
6a
6b
1
1
2
See drawing 6b. Press the Battery Cover (27) back onto
the Console (1).
5
Make sure that the walking belt is properly tightened (see
SYMPTOM 3 on page 8).
3
27
7. Remove the paper backing from the Adhesive Clip (30).
Press the Adhesive Clip onto the Left Frame Endcap (24)
in the indicated location. Press the Hex Key (20) into the
Adhesive Clip.
7
20
30
24
8. Make sure that all parts are properly tightened before you use the treadmill. To protect the floor or carpet,
place a mat under the treadmill.
5
TREADMILL OPERATION
LUBRICATING THE WALKING PLATFORM
• Time—This mode displays the elapsed time.
• Odometer—This mode displays the distance that
the walking belt has moved since batteries were
changed.
Before the treadmill is used, the walking platform
should be lubricated. Open the included lubricant
packet. Reach under one side of the walking belt as
far as you can, and apply half of the lubricant to the
walking platform. Then, reach under the other side of
the walking belt and apply the remaining lubricant.
After you have applied the lubricant, walk on the
treadmill for a few minutes to spread the lubricant.
• Calorie—This mode displays the approximate num-
ber of calories you have burned.
• Scan—This mode displays the Speed, Distance,
Time, Odometer, and Calorie modes.
Follow the steps below to operate the console.
1. Turn on the power.
Apply
lubricant
here
To turn on the power, press the console button or
begin walking. Note: If batteries were just installed,
the power will already be on.
2. Track your progress with the six modes.
Apply
lubricant
here
When the power is
turned on, the Scan
mode will be select-
ed and the SCAN
indicator will
STEP-BY-STEP CONSOLE OPERATION
appear. The con-
sole will display the
Speed, Distance,
Time, Odometer, and Calorie modes, for about six
seconds each, in a repeating cycle.
SCAN Indicator
Before the console can be operated, batteries must be
installed (see assembly step 5 on page 5). If there is a
thin sheet of plastic on the console, remove the plastic.
To select only the Speed, Distance, Time,
Odometer, or Calorie mode, press the console but-
ton until only the SPEED, DIST, TIME, ODO, or
CAL indicator appears in the display. Make sure
that the SCAN indicator does not appear.
To reset all modes (except for the odometer mode),
press the console button for about three seconds.
3. Turn off the power.
To turn off the power, simple wait for a few minutes.
If the walking belt is not moved and the console
button is not pressed for a few minutes, the power
will turn off automatically.
The console features six modes:
• Speed—This mode displays your speed, in miles
per hour.
• Distance—This mode displays the number of miles
you have walked.
6
INCLINE ADJUSTMENT
1. Hold the treadmill
in the location
The incline of the treadmill can be adjusted to any of
three angles. To change the incline, first lift the front of
the Frame (29) so the small incline knobs on the sides
of the Frame slide out of the slots in the brackets on
the Uprights (35, 36). Raise or lower the Frame, and
slide the knobs into one of the three sets of slots in the
brackets. Make sure that the knobs are fully insert-
ed at the same height.
shown. CAUTION:
To decrease the
possibility of
injury, bend your
legs and keep
your back
straight. As you
raise the tread-
mill, make sure
to lift with your
legs rather than
your back. Raise the treadmill to the vertical posi-
tion.
35
Bracket
36
2. Hold the treadmill
2
securely with your
29
right hand as
shown. Insert the
Storage Pin (4)
into the hole in the
left side of the Left
Upright (35) and
into the Frame
(29) as far as it
will go.
29
35
CAUTION:
Make sure that the
incline knobs are fully inserted at the same
height.
Next, press the
ends of the Spring
Clip (21) together,
and slide the
Spring Clip onto
the end of the
RESISTANCE ADJUSTMENT
4
21
To increase the
Storage Pin (4).
intensity of your
workout, you can
adjust the resistance
on the walking belt.
To increase the
resistance, turn the
Resistance Knob
(44) clockwise.To
decrease the resis-
tance, turn the
LOWERING THE TREADMILL FOR USE
1. Hold the treadmill securely with your right hand as
shown in drawing 2 above. Press the ends of the
Spring Clip (21) together, and slide the Spring Clip
off the end of the Storage Pin (4). Pull out the
Storage Pin and pivot the treadmill down a few
inches. Then, reinsert the Storage Pin and reattach
the Spring Clip.
44
Resistance Knob
counterclockwise.
2. Hold the treadmill firmly with both hands, and lower
the treadmill to the floor. CAUTION: To decrease
the possibility of injury, bend your legs and
keep your back straight.
FOLDING THE TREADMILL FOR STORAGE
When the treadmill is not in use, it can be folded to
the compact storage position. CAUTION: You must
be able to safely lift 11 kg (25 lbs.) to raise, lower,
or move the treadmill. Follow the steps at the right to
fold the treadmill.
7
MAINTENANCE AND TROUBLESHOOTING
Most problems can be solved by following the simple steps below. If further assistance is needed,
please call our Customer Service Department.
1. SYMPTOM: THE CONSOLE DOES NOT
FUNCTION PROPERLY
3. SYMPTOM: THE WALKING BELT SLIPS OR IS
OFF-CENTRE
a. Replace the batteries in the console (see assem-
bly step 5 on page 5).
a. If the walking
belt slips
when walked
b. Make sure that the reed switch is properly adjust-
ed (see assembly step 3 on page 4).
on, use the
hex key to turn
both adjust-
c. Make sure that the handrail wire is plugged fully
into the wire on the console (see assembly step 6
on page 5).
ment bolts
clockwise, 1/4
of a turn. When the walking belt is correctly tight-
ened, you should be able to lift each side of the
walking belt 5 to 7 cm (2 to 3 in.). Walk on the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened. Be careful to keep
the walking belt centred.
d. The console, like most electronics, is susceptible
to static electricity build-up caused by certain
types of clothing or by the operation of the tread-
mill. If the display is blank or gives incorrect read-
ings, apply an anti-static spray to the handrail.
Anti-static spray is available where laundry sup-
plies are sold.
b. If the walking
belt has shift-
ed to the left
2. SYMPTOM: THE WALKING BELT DOES NOT
MOVE SMOOTHLY
side, use the
hex key to turn
the left adjust-
a. If the walk-
ing belt is
ment bolt
clockwise, and
overtight-
ened, per-
formance
may be
the right adjustment bolt counterclockwise, 1/4 of
a turn each. Be careful not to overtighten the
walking belt. Walk on the treadmill for a few min-
utes. Repeat until the walking belt is centred.
Walking
Belt
reduced and
the walking
belt may be
permanently
damaged.
Using the
hex key,
c. If the walking
belt has shift-
ed to the right
side, use the
hex key to turn
5–7cm
Bolts
the left adjust-
turn both rear roller adjustment bolts counter-
clockwise 1/4 of a turn. When the tension of the
walking belt is correct, you should be able to lift
each side of the walking belt 5 to 7 cm (2 to 3 in.).
Walk on the treadmill for a few minutes. Repeat
until the walking belt is properly tightened. Be
careful to keep the walking belt centred.
ment bolt coun-
terclockwise,
and the right adjustment bolt clockwise, 1/4 of a
turn each. Be careful not to overtighten the walk-
ing belt. Walk on the treadmill for a few minutes.
Repeat until the walking belt is centred.
8
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition and
adequate rest are essential for successful results.
the first few minutes of exercise, your body uses easi-
ly accessible carbohydrate calories for energy. Only
after the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn
fat, adjust the intensity of your exercise until your
heart rate is between the lower two numbers in your
training zone as you exercise.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals withpre-
existing health problems.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For effective aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your train-
ing zone.
WHY EXERCISE?
Exercise has proven essential for good health and
well-being. A well-rounded exercise program helps to
develop a stronger and more efficient heart, improved
respiratory function, increased stamina, better weight
management, increased ability to handle stress, and
greater self-esteem.
HOW TO MEASURE YOUR HEART RATE
EXERCISE INTENSITY
To measure your
heart rate, stop exer-
cising and place two
fingers on your wrist
as shown. Take a
six-second heartbeat
count, and multiply
the result by ten to
find your heart rate.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows
recommended heart rates for fat burning and aerobic
exercise.
(A six-second count is used because your heart rate
drops quickly when you stop exercising.) If your heart
rate is too high, decrease the intensity of your exer-
cise. If your heart rate is too low, increase the intensity
of your exercise.
WORKOUT GUIDELINES
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers are your “training
zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
Each workout should include the following three impor-
tant parts:
A warm-up, consisting of five to ten minutes of
stretching and light exercise. This will increase your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Burning Fat
Training zone exercise, including 20 to 30 minutes of
exercise with your heart rate in your training zone.
To burn fat effectively, you must exercise at the proper
intensity level for a sustained period of time. During
9
A cool-down, consisting of five to ten minutes of
stretching. Stretching after exercise is effective for
increasing flexibility and helps to offset problems
caused when you stop exercising suddenly.
Instead of waiting for a convenient time to exercise,
plan a specific time. The morning hours work well for
many, and the self-discipline required to rise early and
exercise increases productivity throughout the day. For
others, exercising before dinner helps them to relax.
Whatever time you choose, be consistent.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three
The key to success is to make exercise a regular and
workouts each week, with at least one day of rest after enjoyable part of your everyday life.
each workout. After a few months of regular exercise,
you may complete up to five workouts each week, if
desired.
PART LIST—Model No. WETL0254.0
R0506A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
3
1
1
1
10
2
1
2
1
1
4
1
2
2
2
1
1
1
1
2
2
1
1
1
1
1
Console
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
#
1
1
2
2
4
5
1
1
4
4
1
1
1
4
1
1
1
1
1
8
2
1
1
2
1
1
Frame
Adhesive Clip
Handrail Endcap
Handrail Foam Grip
M8 x 15mm Bolt
M8 Washer
Handrail Wire
M4 x 12mm Screw
Storage Pin
Handrail
Reed Switch/Wire
M5 x 20mm Bolt
Frame Endcap
Front Roller/Flywheel
M5 x 10mm Bolt
Clip
Magnet
M8 Nylon Nut
Base
Left Upright
Right Upright
9
M8 Curved Washer
M8 x 63mm Bolt
Grommet
Warning Decal
Platform Cover, Left
M5 x 16mm Bolt
Frame Endcap, Right
Resistance Control/Cable
Magnet Plate
M5 x 12mm Bolt
M5 Washer
Resistance Magnet
Endcap Foot
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Base Pad
Roller Guard
Base Endcap
Walking Belt
Walking Platform
Hex Key
Spring Clip
Rear Roller Adjustment Bolt
Rear Roller Washer
Frame Endcap, Left
Rear Roller
Wrench
Battery Cover
Hood
Platform Cover, Right
M6 x 60mm Bolt
M6 Nut
Lubricant Pack
User’s Manual
#
# These parts are not illustrated.
Specifications are subject to change without notice. See the back cover of this manual for information about
ordering replacement parts.
10
EXPLODED DRAWING—Model No. WETL0254.0
R0506A
1
34
6
33
27
2
5
4
21
40
35
34
32
3
46
47
33
31
44
10
36
32
12
6
11
3
37
8
31
10
28
13
9
51
52
18
13
37
39
9
8
7
52
13
37
7
41
42
7
19
50
29
7
13
48
13
37
16
34
42
45
7
24
7
25
14
23
16
15
15
7
49
7
17
43
38
17
22
7
23
20
30
49
38
22
26
7
11
ORDERING REPLACEMENT PARTS
To order replacement parts, contact the ICON Health & Fitness, Ltd. office, or write:
ICON Health & Fitness, Ltd.
Customer Service Department
Unit 4, Revie Road Industrial Estate
Revie Road
Beeston
Leeds, LS118JG
UK
Tel:
08457 089 009
Outside the UK: 0 (044) 113 387 7133
Fax: 0 (044) 113 387 7125
To help us assist you, please be prepared to give the following information:
• The MODEL NUMBER of the product (WETL0254.0)
• The NAME of the product (WESLO CARDIOSTRIDE ULTIMA treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) needed (see page 10)
REPRINT
UPDATED STEP 2
WESLO is a registered trademark of ICON IP, Inc.
Part No. 221783 R0506A
Printed in China © 2006 ICON IP, Inc.
|