Model No. WCTL39102
Serial No.
USER'S MANUAL
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, please call:
1-888-936-4266
Mon.–Fri. 8h00 until 18h30 EST
(excluding holidays).
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
12. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 4 if the tread-
mill is not working properly.)
20. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
13. The roller guards must be 32mm (1/8 in.)
from the rear roller. Remove the key and
adjust the roller guards, if necessary.
21. Inspect and tighten all parts of the treadmill
every three months.
22. To change the incline level of the treadmill,
refer to the instructions on page 9. Do not
attempt to change the incline level in any
other way.
14. Wear appropriate exercise attire when using
the treadmill. Do not wear loose clothing that
could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
23. Never drop or insert any object into any
opening.
24. Always unplug the power cord before per-
forming the maintenance and adjustment
procedures described in this manual. Never
remove the motor hood unless instructed to
do so by an authorized service representa-
tive. Servicing other than the procedures in
this manual should be performed by an
authorized service representative only.
15. Never start the treadmill while you are stand-
ing on the walking belt.
16. Always hold the handrails while exercising
on the treadmill.
17. Adjust the speed in small increments.
18. To reduce the possibility of the treadmill
overheating, do not operate the treadmill
continuously for longer than 1 hour.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
19. Never leave the treadmill unattended while it
is running. Always remove the key when the
treadmill is not in use.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
3
BEFORE YOU BEGIN
Thank you for selecting the WESLO CADENCE® 391
treadmill. The natural motion and versatility of tread-
mills have made them the most popular way to get an
effective cardiovascular workout. The CADENCE 391
treadmill blends advanced technology with innovative
design to let you enjoy this effective exercise in the
convenience and privacy of your home. Feel better,
look better, and be healthier in just a few minutes a
day.
please call our Customer Service Department toll-free
at 1-888-936-4266, Monday through Friday 8h00 until
18h30 eastern time (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number is
WCTL39102. The serial number can be found on a
decal attached to the treadmill (see the front cover of
this manual for the location).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Console
Towel Rack
Pulse Sensor
Speed Control
Key/Clip
Upright
Handrails
FRONT
Circuit Breaker
Motor Hood
Walking Belt
Power Cord
Roller Guards
Incline Pin
Foot Rail
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolt
4
ASSEMBLY
Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until
assembly is completed. Refer to the drawings below to identify small parts used in assembly. Assembly requires
an adjustable wrench
(not included).
3/8" x 1" Bolt (18)–1
3/8" Flange Nut (48)–2
3/8" x 1 1/2" Washer
(28)–1
3/8" x 2 3/4" Bolt (49)–2
3/8" x 1 3/4" Bolt (2)–2
1. Raise the Upright (11) to the vertical position. Insert the 3/8” x 1”
Bolt (18) and the 3/8” x 1 1/2” Washer (28) into the lower end of
the Upright. Finger tighten the Bolt into the Frame (59).
1
11
18
28
59
2. Hold the upper end of the Right Handrail (10) under the
Console (3). Insert a 3/8” x 1 3/4” Bolt (2) up into the Handrail,
and finger tighten the Bolt into the plate under the Console.
2
3
1
Attach the Left Handrail (1) in the same manner.
2
10
3. Insert a 3/8” x 2 3/4” Bolt (49) into the lower end of the Right
Handrail (10) and through the Frame (59). Reach under the
Frame and tighten a 3/8” Flange Nut (48) onto the Bolt.
3
59
Attach the Left Handrail (not shown) in the same manner.
10
Tighten all Bolts used in steps 1 and 2.
49
48
4. Remove the paper backing from the Adhesive Clip (64). Press
the Adhesive Clip onto the Right Endcap (63) in the indicated
location. Press the Allen Wrench (65) into the Adhesive Clip.
4
63
65
64
5
5. The Console (3) requires two "AA" batteries (not included).
5
3
Alkaline batteries are recommended.
15
Slide the Battery Cover (15) up as shown. Press two batteries into
the battery compartment, with the negative (–) ends of the batteries
touching the springs. Close the battery cover.
Batteries
6. Make sure that all parts are tightened before you use the treadmill. Note: To protect the floor or carpet from
damage, place a mat beneath the treadmill.
PROPER EXERCISE FORM
The instructions on pages 7 to 9 of this manual explain the operation and adjustment of the treadmill. For maxi-
mum treadmill performance, it is important to maintain proper form when walking on the treadmill. The drawing
below demonstrates the proper form. Be sure to remember the following important guidelines:
• Always hold the handrails when stepping on
and off the treadmill, and when exercising on
the treadmill.
• Always stand on the foot rails when turning on
the power or starting the walking belt. The walk-
ing belt may not start while you are standing on it.
• While walking on the treadmill, rest your hands
on the handrail, keep your back straight, and
lean forward slightly. Do not lean back or push
forward against the walking belt with your feet. If
you slow the walking belt with your feet, it may
come to a stop. If this happens, stand on the foot
rails until the walking begins to move again.
• To change the incline level of the treadmill,
refer to page 9. Do not attempt to change the
incline level any other way. The incline range of
the treadmill is 11% to 14%. This range is ideal for
maximum treadmill performance.
6
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right).
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
CUL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
7
DIAGRAM OF THE CONSOLE
Pulse Display
Speed Control
Monitor Display
On/Reset
Button
Note: If there is a thin sheet of clear
plastic on the console, remove it.
Clip
Pulse Sensor
Key
Insert the key fully into the power switch.
1
CAUTION:
Before operating the con-
sole, read the following important precautions.
Note: The two dis-
plays will not
appear when the
key is first insert-
ed.
• Do not stand on the walking belt when turning
on the power.
• Always wear the clip while operating the tread-
mill. When the key is removed from the con-
sole, the power will shut off.
Key
• After the speed control is moved, there will be
a pause before the walking belt begins to move.
Press the On/Reset button.
2
3
The two displays
will appear. Note:
If batteries were
just installed, the
displays will
• Adjust the speed in small increments until you
are familiar with the treadmill.
• To reduce the risk of electric shock, keep the
console dry. Avoid spilling liquid on the con-
sole and use only a sealed water bottle.
already appear.
Reset the speed control and start the walking
belt.
STEP BY STEP CONSOLE OPERATION
Slide the speed
control fully to the
left, to the
"RESET" position.
Next, slide the
control to the right
until the walking
belt begins to
Make sure that the power cord is properly plugged in
(see HOW TO PLUG IN THE POWER CORD on page
7). Next, step onto the foot rails of the treadmill. Find
the clip attached to the key (see the drawing above).
Slide the clip onto your waistband. Follow the steps on
pages 8 and 9 to operate the console.
move at a slow speed.
8
Carefully step onto the walking belt and begin
walking. Change the speed of the walking belt as
desired by sliding the speed control. Note: To stop
the walking belt, slide the speed control to the
"RESET" position.
your pulse will be displayed. Hold your thumb on
the sensor for another 15 seconds for the most
accurate reading. If the displayed pulse appears
to be too high or too low, or if your pulse is not
displayed, lift your thumb off the sensor and allow
the display to reset. Press down again on the sen-
sor as described above. Make sure that your
thumb is positioned as shown, and that you are
applying the proper amount of pressure. Try the
sensor several times until you become familiar
with it. Always stand still while measuring your
pulse.
Monitor your progress with the two displays.
4
Time/Distance dis-
play—The left display
shows the elapsed
time and the distance
that you have walked
or run. Every few sec-
onds, the display will
When you are finished exercising, stop the
walking belt and remove the key.
6
change from one number to the other.
Step onto the foot rails, slide the speed control to
the RESET position, and remove the key from the
console. The displays will turn off a few minutes
after the key is removed. Note: Any time that the
walking belt is stopped for a few minutes, the
displays will automatically turn off to conserve
the batteries.
Cals/Fat Cals/
Speed/Pulse
display—The right dis-
play shows the approx-
imate number of calo-
ries and fat calories
you have burned (see
FAT BURNING on
page 12) and the
Mode Bar
HOW TO CHANGE THE INCLINE OF THE TREADMILL
speed of the walking belt. Every few seconds, the
display will change from one number to the next.
The left mode bar will appear when the number of
calories is shown; the right mode bar will appear
when the number of fat calories is shown. This
display will also show your heart rate when the
pulse sensor is used.
To vary the intensity of your exercise, the incline of the
treadmill can be changed. There are three different
incline levels. Before changing the incline, remove
the key and unplug the power cord.
To change the
1
Incline Pin
Incline Leg
incline, carefully lay
the treadmill on its
left side. Remove
the incline pin from
the right incline leg
as shown in draw-
ing 1. Adjust the
incline leg to the
desired height and
fully re-insert the
incline pin. Make
sure the incline pin
is in the “locked”
position shown in
drawing 2. Lay the
To reset the displays, press the On/Reset button.
Measure your pulse, if desired.
To use the pulse
Frame
5
sensor, stand on
the foot rails and
place your thumb
on the pulse sen-
sor as shown. The
pulse sensor is
Pulse Sensor
2
Incline Pin
pressure-activat-
ed. Fully press
down the pulse sensor. Do not press too hard,
or the circulation in your thumb will be
restricted, and your pulse will not be detected.
Next, slightly raise your thumb until the heart-
shaped indicator in the Cals/Fat
treadmill on its right side. Repeat the procedure for the
left incline leg.
CAUTION: Before using the treadmill, make sure
that both incline pins are fully inserted at the same
height. Do not use the treadmill with the incline
pins removed.
Cals/Speed/Pulse display flashes steadily. Hold
your thumb at this level. After 5 to 10 seconds,
9
TROUBLESHOOTING AND STORAGE
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies to your treadmill and follow the steps listed. If further assistance is needed, please call our
Customer Service Department toll-free at 1-888-936-4266, Monday through Friday, 8h00 until 18h30 east-
ern time (excluding holidays).
1. SYMPTOM: THE POWER DOES NOT TURN ON
a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged
into a properly grounded outlet (see page 7). Use only a CUL-listed surge suppressor, rated at 15 amps,
with a 1 mm2 (14-gauge) cord of 1.5 m (5 ft.) or less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console (see step
1 on page 8).
c. Check the circuit breaker located on the treadmill frame near
the power cord. If the switch protrudes as shown, the circuit
breaker has tripped. To reset the circuit breaker, wait for five
minutes and then press the switch back in.
Tripped
Reset
2. SYMPTOM: THE POWER TURNS OFF DURING USE
a. Check the circuit breaker located on the treadmill frame near the power cord. If the circuit breaker has
tripped, the switch will protrude (see the drawing above). To reset the circuit breaker, wait for five minutes
and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console (see step 1 on page 8).
3. SYMPTOM: THE DISPLAYS OF THE CONSOLE DO NOT FUNCTION PROPERLY
a. Check the batteries in the console (see assembly step 5 on page 6). Most problems are the result of drained
batteries.
b. If the speed display does not show a correct reading, remove the
b
key and UNPLUG THE POWER CORD. Remove the four
1/8”
73
screws from the sides and front of the hood. Carefully remove the
hood. Locate the Reed Switch (73) and the Magnet (75) on the
left side of the Pulley (43). Turn the Pulley until the Magnet is
aligned with the Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 3 mm (1/8 in.). If
necessary, loosen the Screw (53) and move the Reed Switch
slightly. Retighten the Screw. Re-attach the hood and run the
treadmill for a few minutes to check for a correct speed reading.
43
75
53
Top
View
4. SYMPTOM: THE WALKING BELT SLOWS OR STOPS WHEN WALKED ON
a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 7.
b. Increase the incline of the treadmill (see HOW TO CHANGE THE INCLINE OF THE TREADMILL on page 9).
c. Make sure that you are using proper form when walking on the treadmill (see PROPER EXERCISE FORM
on page 6).
d. If the walking belt still slows when walked on, please call our Customer Service Department.
10
5. SYMPTOM: THE WALKING BELT IS OFF-CENTER
a. If the walking belt has shifted to the left, first remove the key and
UNPLUG THE POWER CORD. Using the allen wrench, turn the
rear roller adjustment bolt clockwise 1/4 of a turn. Plug in the
power cord, insert the key and run the treadmill for a few min-
utes. Repeat until the walking belt is centered.
a
b. If the walking belt has shifted to the right, first remove the key
and UNPLUG THE POWER CORD. Using the allen wrench, turn
the rear roller adjustment bolt counterclockwise 1/4 of a turn.
Plug in the power cord, insert the key and run the treadmill for a
few minutes. Repeat until the walking belt is centered.
b
STORAGE
Unplug the power cord when the treadmill is not in use.
Remove the bolt and nut from the lower end of each handrail.
Remove
Remove the bolt from the upper end of each handrail.
Remove
Remove the bolt and washer from the lower end of the upright. Lay
the upright on the treadmill. Keep all bolts and washers in a
secure location.
Remove
Remove the batteries from the console and cover the treadmill dur-
ing extended periods of storage.
11
CONDITIONING GUIDELINES
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your
exercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up
increases your body temperature, heart rate and circu-
lation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-
exercise problems.
EXERCISE FREQUENCY
Fat Burning
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months, you may com-
plete up to five workouts each week if desired.
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes does your body
The key to success is to make exercise a regular and
enjoyable part of your everyday life.
12
PART LIST—Model No. WCTL39102
R1003A
Key No. Qty.
Description
45
1
Walking Belt
Key No.
Qty.
Description
1
2
3*
4
5
6
7
8
9
1
2
1
1
2
5
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
4
4
6
1
2
1
1
1
1
1
1
1
2
9
2
2
2
2
1
4
1
1
1
Left Handrail
3/8” x 1 3/4” Bolt
Console
Upright Wire Harness
Console Cage Nut
Console Screw
Pot Wire
Console Cable Loom
Key/Clip
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
#
2
1
2
2
1
1
4
5
4
2
1
1
1
1
2
1
1
1
1
1
1
1
1
6
4
1
2
1
1
1
1
9
1
2
2
2
4
1
1
1
Foot Rail
Pulley/Flywheel
3/8” Flange Nut
3/8” x 2 3/4” Bolt
Controller
Controller Plate
Plastic Stand-Off
Electric Screw
4” Cable Tie
8” Cable Tie
Tie Holder
Potentiometer
Speed Control
Frame
10
11
12
13
14
15
16
17*
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Right Handrail
Upright
Motor Swivel Bolt
Upright Cage Nut
Motor Swivel Nut
Battery Cover
Motor
Motor/Pulley/Flywheel
3/8” x 1” Bolt
Motor Tension Washer
Star Washer
Rubber Pad
Tension Spring
Roller Ground Wire
Right Endcap
Adhesive Clip
Allen Wrench
Short Roller Adjustment Bolt
Left Endcap
Rear Roller
Platform Screw
Hood Screw
Hood
Roller Guard Screw
Reed Switch/Sensor Wire
Roller Tension Nut
Magnet
Motor Tension Nut
Wire Clip
Hood Anchor
Anchor Screw
Upright Pivot Nut
Upright Pivot Washer
Upright Cable Loom
3/8” x 1 1/2” Washer
Reed Switch Clip
Power Cord
Circuit Breaker
Upright Pivot Bolt
Grommet
Frame Endcap
Screw
Incline Pin
Incline Leg Cap
Incline Leg
Belt Guide
Motor Belt
#8 Flat Washer
Long Roller Adjustment Bolt
Roller Guard
Handgrip
3/8” Cap Washer
Belt Guide Screw
8” Green Ground Wire
8” White Wire, Male/Female
User’s Manual
Front Roller Adjustment Bolt
Adjustment Washer
Safety Cover
Front Roller/Pulley
Walking Platform
#
#
* Includes all the parts in the box.
# Indicates a non-illustrated part.
Specifications are subject to change without notice. See the back cover for information about ordering replace-
ment parts.
13
EXPLODED DRAWING—Model No. WCTL39102
R1003A
15
58
57
3*
6
4
2
5
1
9
18
6
7
6
80
20
5
8
21
14
47
19
2
17*
70
6
10
71
11
16
12
70
25
18
26
30
31
28
22
27
26
53
24
23
73
32
29
76
43
75
33
49
13
34
53
40
70
48
41
77
42
44
35
46
46
77
69
72
45
77
35
74
72
41
3
36
61
35
39
79
68
82
67
81
48
37
41
49
59
66
51
53
60
24
53
56
53
50
63
64
55
41
52
62
78
54
65
14
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-936-4266, Monday through
Friday 8h00 until 18h30 Eastern Time (excluding holidays). When ordering parts, please be prepared to give the
following information:
• The MODEL NUMBER of the product (WCTL39102)
• The NAME of the product (WESLO CADENCE® 391 treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and the DESCRIPTION of the part(s) (see page 13 of this manual).
PLACE
STAMP
HERE
ICON of Canada, Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
15
LIMITED WARRANTY
ICON OF CANADA, INC., (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of one (1) year from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center, to prod-
ucts used for commercial or rental purposes, or to products used as store display models. No other war-
ranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some provinces do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you. The war-
ranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some provinces do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to
province or so specified by the retailer of your equipment.
ICON OF CANADA, INC., 900 de l’Industrie, St. Jerôme, QC J7Y 4B8
™
®
o f / d u C a n a d a I n c .
PRODUCT WARRANTY REGISTRATION
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUNTY:
PHONE:
POSTCODE:
MODEL NO.
RETAILER NAME:
SERIAL NO.
PURCHASE DATE:
RETAILER ADDRESS:
1) Primary user(s) of product:
8) Did you consider purchasing fitness equipment from another
manufacturer?
❏❏❏Male
❏❏❏Female
❏❏❏Family
❏ 55–64
❏ No
❏ Yes
2) Age of primary user:
❏❏❏0–24
What other manufacturer?
❏ 35–44
❏ 45–54
❏ 25–34
❏ 65 and over
9) Based on your impression of what you have purchased,
would you buy another ICON product?
3) Annual household income:
❏ Yes
❏ No
❏ No Opinion
❏ 0–9,999
❏ 15,000–19,999
If not, what other brand equipment would you purchase?
❏ 10,000–14,999
❏ 20,000+
4) How many times a week do you exercise?
10) What other type of exercise equipment do you own?
❏ Less than 3 times ❏ 3 times or more
❏ Bicycle
❏ Exercise Cycle ❏ Treadmill
❏ Weight Bench ❏ Stepper
❏ Other
❏ Home Gym
❏ Cardio Glide
5) Have you ever purchased an ICON product before?
❏ Yes ❏ No
11) Which type of magazines do you read regularly?
6) Where did you first see or hear about ICON products?
❏ Sports
❏ Fitness
❏ Motoring
❏ Magazine
❏ Newspaper Ad
❏ Other
❏ Friend/relative
❏ Business
❏ Computer
❏ General
❏ Store
12) Do you wish to be sent further bulletins about ICON products?
❏ Yes ❏ No
7) What was the primary reason for purchasing this ICON product?
❏ Store Employee ❏ Television Ads ❏ Colour
❏ Electronic Features ❏ Magazine Ads ❏ Price
THANK YOU FOR YOUR TIME
© 2003 ICON of Canada, Inc.
❏ Product Design
❏ Other Features
❏ Product Innovation
WESLO is a registered trademark of ICON Health & Fitness, Inc.
Part No. 204163 R1003A Printed in Canada © 2003 ICON Health & Fitness, Inc.
|